Back to top of page

Select the correction type to output:

• CMR

• RTCM

• REPEAT-RTCM

• NMEA

• RT17/RT27

• BINEX

• GSOF

• OmniSTAR

• 1 PPS TIME TAG

Select the correction type to output:

• CMR

• RTCM

• REPEAT-RTCM

• NMEA

• RT17/RT27

• BINEX

• GSOF

• OmniSTAR

• 1 PPS TIME TAG

This option allows correction data to be received securely from an NTRIP Caster or Trimble RTX over IP. The NTRIP source may be:

• A Trimble VRS Network

• A Trimble NTRIP Caster

• The Trimble Internet Base Station Service (IBSS)

  The Internet Base Station Service (IBSS) is a Trimble service that allows users to simply and easily use the internet to make their base station available to rovers.

• The global Trimble RTX correction service

• Another NTRIP compliant correction source

NTRIP version 2 is supported in firmware version 4.14 and later.

Status – Indicates the current status of the NTRIP connection:

Enable – Select to enable NTRIP Client.

RTXIP mode – Select this mode to obtain the Trimble RTX service over IP. The receiver requires a current RTX subscription to operate in this mode.

Ntrip Caster http(s):// – The address and port of the NTRIP Caster that the receiver will connect to in order to receive correction data.

Enable SSL/TLS – Select this check box to enable the SSL or TLS protocol. When selected, the connection to the remote NtripCaster uses the SSL/TLS secure connection protocol. When it is not selected, the connection may not be secured. Before enabling, verify that the remote NtripCaster supports the SSL/TLS protocol.

User Name – Enter the username required to log on to the server.

Password – Enter the password required to log on to the server.

Verify Password – Re-enter the password required to log on to the server.

Mount Point – Enter name of the correction stream to which you are connecting on the NTRIP Caster if known, or select from the list using the Get Mount Points button.

Get Mount Points – Use this button to obtain a list of available base stations for selection. The list is ordered with the closest at the top of the list and includes the distance from the receiver's current position in km.

This option enables the receiver to connect to IBSS or an NTRIP Caster to send correction data securely across the internet.

Status – Indicates the current status of the NTRIP connection:

Enable – Select this check box to enable NTRIP Server.

NTRIP Version – NTRIP Server supports either NTRIP version 1 or 2.

NTRIP Caster http(s):// – The address and port of the NTRIP Caster that the receiver will connect to in order to send or receive data.

Enable SSL/TLS – Select this check box to enable the SSL or TLS protocol. When selected, the connection to the remote NtripCaster uses the SSL/TLS secure connection protocol. When it is not selected, the connection may not be secured. Before enabling, verify that the remote NtripCaster supports the SSL/TLS protocol.

Mount Point – The name of the correction stream the receiver is supplying to the NTRIP Caster.

Username – Enter the username required to log on to the server.

Password – Enter the password required to log on to the server.

Verify Password – Re-enter the password required to log on to the server.

Identifier – The unique identifier for the receiver (NTRIP Server) supplying the correction stream.

Country – An optional identifier to help distinguish which country the NTRIP Server is in.

Network – An optional identifier to help distinguish which network the NTRIP Server is a part of.

Select the correction type to output:

• CMR

• RTCM

• OmniSTAR

  NOTE – OmniSTAR is not available in IBSS Mode.

NTRIP Caster

There are three NTRIP Caster ports available. For each port, a maximum of 10 users can request data, which means that a total of 30 users can simultaneously request data. When the factory defaults are applied, the three NTRIP Caster ports will be automatically configured to output CMRx on port 2101, CMR on port 2102 and RTCMv2.1 on port 2103.

Enable – Select this check box to enable this NTRIP Caster port.

Port – Source Port number of the caster host.

Enable SSL/TLS – Select this check box to enable the SSL or TLS protocol.

Identifier – The unique identifier for the NTRIP Caster.

Country – Enter the character country code, for example USA, DE.

Mount Point – Enter the name of the output stream, such as its type. Users must enter this name to connect to the port.

Select one source of corrections:

• CMR

• RT17/RT27

• RTCM

• OmniSTAR

Serial1 / COM1, Serial2 / COM2, Serial3 / COM3, Serial4 / COM4

The serial ports can be configured from here. The BD960 and BD970 do not have a fourth serial port. Serial ports 1 and 3 do not support flow control, but serial port 2 does. On the BD982 receiver flow control is not supported.

The BD940 has four serial ports. Port 1 and Port 3 DO NOT have flow control. Flow control is ENABLED on Port 2 and Port 4.

The BD99x series and BX992 has two serial ports. Port 1 DOES NOT have flow control. Flow control is ENABLED on Port 2.

Serial Port Setup – Set the appropriate baud rate, parity, and flow control for the port.

Select the correction type to output:

• NMEA

• BINEX

• GSOF

• OMNISTAR

• 1 PPS TIME TAG

• MET-TILT

Back to top of page

Back to top of page

CAN 0

CAN – CMR, NMEA, or GSOF data can be streamed over this port.

For more detail on the format of these messages and cabling, contact Trimble.

One of the following groups appears, depending on the option selected in the drop-down list at the top of the page:

• CMR

• NMEA

• GSOF

• CANSPECTRA (not all OEM GNSS receivers)

Back to top of page

REPEAT-RTCM

This feature allows an external source of RTCM corrections to be repeated to another port. The external source can be OmniSTAR VBS (if installed).

The following fields appear when you select REPEAT-RTCM from the Output Type list at the top of the page.

Use VBS as source – Select this check box to use the decoded OmniSTAR VBS service to populate an RTCM DGPS correction stream. The RTCM DGPS correction stream can be output on Ethernet, Serial, or USB ports. This output is available when the receiver is in any operating mode and can also be selected from the front panel Port menu. Only available when a valid OmniSTAR VBS subscription is loaded in receiver that supports OmniSTAR.

NMEA

The following fields appear when you select NMEA from the Output Type list at the top of the page.

NMEA Messages – Select which NMEA messages will be output on this port. See NMEA-0183 messages: Overview.

Standard – Select which standard to use for the compliant messages.

• NMEA Legacy – Output messages comply the National Marine Electronics Association (NMEA) 0183 Standard for Interfacing Marine Electronic Devices, Version 4.0, November 1, 2008. This is the default selection.

• IEC61162-1:2010/NMEA 0183 V4.10 – Output messages will comply with the International Electrotechnical Commission (IEC) 61162-1, Edition 4 2010-11.

Variations from standard

Report max DQI=2 NMEA GGA string – When enabled, the Quality Indicator field in the GGA output message will never be greater than 2 (Differential GPS). Use this only with legacy systems that do not fully support the NMEA standard.

Report max correction age 9 sec in NMEA GGA string – When enabled, the Age of differential data field in the GGA message will never be greater than 9 sec. Use this only with legacy systems that do not fully support the NMEA standard.

Report extended information in NMEA GGA and RMC strings – By default, this check box is enabled to provide high-precision position data in the NMEA messages. Clear this check box to conform to the NMEA standard message length of 82 characters.

Report GST message always as GPGST – When enabled, the NMEA talker ID will always be $GP for the GST message no matter what constellation is being tracked. This is required for some legacy systems using this NMEA output which have not yet been updated to follow the NMEA standard. By default, this is disabled.

Report legacy talker ID – When enabled, this forces the following sentences to always use “GP” as the talker ID: GGA, MSS, DTM, GLL, HDT, RMC, ROT, VTG, and ZDA.

Report RTK Fixed if 1σ estimated error is less than horizontal and vertical precision – (BD9250, BD940, BD990, BD992 only) Select this check box to provide further control of the reported precision in a NMEA position output (eg. GGA), in particular when IonoGuard is active and scintillation is an issue.

RT17/RT27

The RT17/RT27 option is available when the Binary Outputs option is installed in the receiver. See Receiver Options. The RT17 is a GPS-only data stream. The RT27 is an all GNSS data stream.

The RT17 and RT27 data streams are comprised of data from Response 57h, RAWDATA (Position or real-time survey data report) and Response 55h, RETSVDATA (Satellite information reports).

The following fields appear when you select RT17/RT27 from the Output Type list at the top of the page.

Epoch Interval – This defines the rate at which the RT17/RT27 messages are output. Check boxes are provided to enable the output of measurements and/or positions.

• Measurements – Select this check box to output raw observables.

Antenna

Options

• Concise – Select this check box to output a more compact message containing the raw observables. This only applies to the RT17 output.

• R-T Flag – Select this check box to output IODE values and cycle-slip counts. This only applies to the RT17 output.

• Ephemeris – Select this check box to output the satellite ephemeris when received.

• Send Raw GPS Data – Select this check box to output the raw data extracted from the GPS satellites. This only applies to the RT17 output.

• Send Raw GNSS Data – Select this check box to output the raw data extracted from the GNSS satellites. This only applies to the RT27 output.

• Send Raw SBAS Data – Select this box to output the raw data extracted from the SBAS satellites.

• Include SV Flags2 – Select this box to output SV FLAGS2 data. This only applies to the RT27 output.

• Multi-System Support – Select this check box to output the observables for all GNSS satellites (this will output the RT27 data format).

• Smooth Pseudorange – Enable Pseudorange smoothing.

• Smooth Phase – Enable Phase smoothing.

• Include Doppler – Select this box to output Doppler measurements. This only applies to the RT27 output.

• Include FLL Measurements – Select this box to output Frequency Lock Loop measurements, in addition to Phase Lock Loop measurements. This only applies to the RT27 output.

L2 Signal – Outputs data from the L2 signal. The options are Legacy with L2 - CS fallback, L2C or L2E.

GPS Ephemeris – Outputs the GPS ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

SBAS Ephemeris – Outputs the SBAS ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

The following fields appear when the Multi-System Support check box is enabled.

GLONASS Ephemeris – Outputs the GLONASS ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

Galileo Ephemeris – Outputs the Galileo ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

QZSS Ephemeris – Outputs the QZSS ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

BeiDou – Outputs the BeiDou ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

NavIC Ephemeris – Outputs the NavIC ephemeris when a new one is available, or every 10 to 300 seconds, or can be turned off.

Almanac – Checks for an updated almanac when a new one is available, or can be set to check every 10 to 300 seconds, or turned off

BINEX

GSOF

The following fields appear when you select GSOF (General Survey Output Format) from the Output Type list at the top of the page.

GSOF Messages – Select which GSOF messages will be output on this port. See GSOF Messages: Overview.

The following fields appear when you select OmniSTAR from the Output Type list at the top of the page.

Only available when a valid OmniSTAR subscription is loaded in a receiver that supports OmniSTAR.

DATA for OmniSTAR – Enables the demodulated OmniSTAR data output on this port. This output can then be used as an External OmniSTAR input on a non-Trimble OmniSTAR-capable receiver that has a valid and appropriate OmniSTAR subscription.

DATA for Trimble – Enables the demodulated OmniSTAR data output on this port. This output is the same raw data as above with a TRIMCOMM wrapper (0xC4) to support use as an External OmniSTAR input on a Trimble receiver. The receiver must have a valid and appropriate OmniSTAR subscription.

DEBUG – Enables/Disables DEBUG OmniSTAR output on this port.

1 PPS TIME TAG

The following fields appear when you select 1PPS TIME TAG from the Output Type list at the top of the page.

1PPS Time Tag – Enables the ASCII Time tags. The time tag provides the UTC time of the 1PPS pulse and is output approximately 800 milliseconds before the pulse.

To enable the 1PPS pulse, see Receiver Configuration - General.

MET-TILT

• Command

• Schedule

This setting is used to support meteorological and tilt sensors. This option is available only with serial ports. It allows up to six different fields that allow serial poll type commands to be sent to MET or TILT sensors. The responses are recorded in the receiver's internal memory. If a RINEX file is generated from the associated T02 file, the appropriate and associated *.met and/or *.05m files will be generated.

Serial port 2, when set to MET-TILT, has a power output option that can supply up to 3.6 W @12 V DC from pin 9 of serial port 2.